After Hours Emergency Parts:
256-998-2806
After Hours Emergency Service:
256-777-7564
After Hours Emergency:
270-484-8299
Exmark LRE801GKA604A3
As the most affordable model in the Lazer Z line, the all-new 2025 Lazer Z E-Series delivers an unbeatable combination of cut quality, productivity, durability and value. Select from 48-, 52-, or 60-inch UltraCut Series 4 cutting decks, all equipped with a newly redesigned discharge chute that distributes clippings over a wider area. A choice of twin-cylinder Kawasaki, Kohler, or Vanguard twin-cylinder commercial engines are available, all equipped with heavy-duty external air filters. Power is delivered through unitized Hydro Gear pump and motor units for up to 11 mph forward ground speeds. A new full-suspension operator seat increases operator comfort during long work days.
Shopping Tools
LRE801GKA604A3 Features & Benefits
Unibody Frame
The Lazer Z E-Series utilize a one-piece unibody frame that delivers increased durability with fewer parts –– a classic case of “less is more”.
Less Time At The Pump
Lazer Z E-Series models feature a single 9.5-gallon fuel tank with a single fill location.
Ultracut Series 4 Deck
Built from formed and welded high-strength steel, UltraCut Series 4 full-floating decks feature maintenance free spindles with splined blade drivers to stop bolt tightening on impacts. The idler arm pivot bearings are also maintenance free.
Tool-less Belt Removal
The deck and hydro belts can be installed and removed without tools.
Reduced Maintenance
With just two annual grease points and maintenance-free sealed bearing spindles, the Lazer Z E-Series delivers maximum performance with minimum maintenance.
LRE801GKA604A3 Specs & Compare
| Width / Cutting Deck | 60" |
| Drive | Hydro-Drive |
| Starter | Electric |
| Steering Control | Hydraulically dampened twin levers adjustable both fore and aft. Also has 2-position height adjustment. |
| Caster Forks | .50" thick caster yoke arms. |
| Front Caster Tires | 13 x 6.5-6, smooth tread, pneumatic. Sealed ball bearings. |
| Drive Tires | 24 x 12-12, 4 ply Super Turf TL |
| Safety Package | Operator Presence Controls (OPC) and drive system interlock, with safety interlock system indicators. |
| Parking Brake | Lever actuated internal wet disc brake |
| Tractor Frame | Unibody, welded, heavy-duty 1.5" x 3" tubular steel. |
| Blade Spindles | No maintenance, sealed and non-greasable spindles; 7.75"-diameter cutter housing with 25mm (.98") diameter spindle shaft and splined blade driver. |
| Electrical | 12-volt battery with 15-amp alternator. |
| Standard Features | Engine hour meter and cup holder |
| Seat | Deluxe suspension seat, foam flip-up armrests, and integral safety switch. Adjustment: Fore and aft from operator's position. |
| Power Components | |
| Transmission Speeds | Infinitely Variable |
| Engine Brand | Kawasaki® |
| Engine Model | FX801V |
| Engine Displacement | 852 cc |
| Engine Series | V-Twin |
| Fuel System | Carbureted |
| Speed | Infinitely variable speed selection from 0-11.0 mph forward, 0-6.0 mph reverse. |
| Engine Spec | FX801-AS31-R |
| Engine Speed | 3750 RPM |
| Air Filter | Heavy-duty canister air filtration system |
| Fuel Capacity | 9.5-gallon single fuel tank with single fill location |
| Drive Description | Dual Hydro-Gear ZT-4400, hydrostatic transmission with charge pumps, relief valves and independent, replaceable filters. |
| Fuel Type | Gas Carbureted |
| PTO Engagement | MagStop Electromagnetic 175 ft-lb clutch with spot brake |
| Drive Wheel Release | Allows unit movement without engine running. |
| Fuel Indicator | Mechanical float |
| Deck Lift | Standard; foot-controlled deck lift changes cutting height and lifts the deck to maneuver around obstacles, or place in transport position. |
| Carb Compliant | No |
| ROPS | 2-post foldable ROPS standard with seat belt and latch. |
| Decks | |
| Deck Style | Floating Deck |
| Deck Style Description | Full-floating UltraCut Series 4. Side discharge standard, with molded discharge chute and option to bag or mulch. |
| Deck Construction | 10-gauge high strength alloy top that is formed and continuously seam welded, with 7-gauge side skirt, and 7-gauge reinforcement plate welded to spindle mounting locations for improved strength. |
| Cutting Heights | 1.5" to 5.5" in 0.25" increments |
| Blade Tip Speed | Approximately 18,500 fpm. |
| Blades | 3 blades at 20.50" Length |
| Dimensions | |
| Width | 72.7" |
| Height | 70.1" |
| Length | 84.6" |
| Curb Weight | 1080s |